ADE NUWAcc PRO (RD3-021c PRO) Motion Awake Green Dot for Canik Mete SFX, Smith Wesson MP 380 S

ADE NUWAcc PRO (RD3-021c PRO) Motion Awake Green Dot for Canik Mete SFX, Smith Wesson MP 380 S

ADE Advanced Optics NUWAcc is the first and only red dot with RMRcc footprint that has top battery loading system. There is no need to remove the sight to change the battery, that requires re-sight in and waste ammo. Battery life is approximately 500 to 800 hours depending on the brightness setting.

Easy to Fit

One of the first questions you might have when discussing any new red dot is, what will it fit? Well, as evident in the list below, the NUWAcc right out of the gate fits a multitude of the most popular concealed carry pistols on the market through either direct adaptation to the firearm, if it is an optics-ready model, or through the simple addition of a mounting plate that is compatible with RMRcc footprint. You must confirm your pistol has the RMRcc optic plate or cut, otherwise, it does not fit.

Motion Awake

With Motion Activated or Motion Awake function, while the NUWAcc PRO is turned on, the red dot illumination goes to sleep after five minutes of inactivity, but when any motion or vibration is detected, it instantly switches on illumination at the previous brightness setting. Operates with a single CR1632 battery. 6 daylight brightness settings and 1 NV setting. The Night Vision Dot is not visible to the human eye, it can only be seen through night vision. Battery life can go up to 10,000 hours. 

Design

ADE NUWAcc created an iron sight curve at the end of the body and also added two white dots on the curve. For the rear part of the red dot to become a backup iron sight. With the ultra-short design, the red dot provides a distance or gap on some full-size optics-ready pistols, to give enough distance to be a co-witness backup sight, in addition to the LED dot and pistol-equipped iron sight. For non-optics-ready pistols that need to use an optic plate or adapter to replace the pistol manufacturer-equipped rear sight, ADE NUWA's rear white dot will act as a pistol factory original rear sight for co-witness.

Added Features and Compatibility

ADE NUWAcc is manually activated by pressing the on and off switch. Press and hold the switch for 2 seconds to turn it on and off, and quickly press to adjust the brightness from low to high. It comes with 3 pairs of screws for Sig P365XL/X, Springfield hellcat OSP, and Canik TP9 Elite SC only. The provided screws might not work with every compatible pistol listed. ADE makes the red dot accept the industrial standard footprint. The pistol manufacturer makes the optic cut and slide for the same footprint, but they have their own opinions to decide which type screws the screw holes take. ADE does not know the screw spec every pistol manufacturer used for their screw hole. Please ask the pistol manufacturer what screw specs they used on the hole and ask them to provide the screw. If you can’t get the screw to work properly, we recommend going to a local hardware store such as ACE Hardware to get the right size. ADE RD3-018 Spike, RD3-021 Nuwa and pro, and RD3-030 Apollo fit optic cut/optic plate that is compatible with shield RMS/RMSC/Deltapoint Pro footprint. ADE RD3-021 NUWAcc fit optic cut/optic plate/ that is compatible with Trijicon RMRcc footprint.

Pocket-Friendly 

ADE Advanced Optics first made its appearance in the firearms accessory industry by doing private label production for several Major manufacturers and retailers. During this period, Ade Advanced Optics began receiving requests from numerous customers for access to the affordable, high-quality products that Ade Advanced Optics was capable of producing. By soliciting feedback from both clients and end users in 2010, Ade Advanced Optics was able to overcome the challenges a new company often faces when entering a global market and industry, especially one as competitive as the shooting, hunting, and outdoors industry.